12V 24V 10A Solar charge controller Solar charged protector
12V / 24V 10A PWM solar charge controller supply by UNICELL in Singapore
UNICELL a Leading IT product supplier in Singapore Malaysia Indonesia Philippines Brunei and Thailand since 1986 , we carry more the 66,000 model
Order code : SLP2010-10A
12V 24V Auto 10A Solar charge controller Solar charged protector
Product description:
12V and 24V Auto Solar charge controller, have battery capacity indicator. Also carry with overload, short circuit, lighting, under voltage, over voltage, over charged, anti-access protection.
The product is used to control Solar Panel and battery in Solar System automatically. Here is the Solar Panel Configuration list with different rated voltage (12V and 24V).
FUCTION:
1. Over-load protection
2. Short circuit protection
3. Lightning protection
4. Under-voltage protection
5. Over-charging protection
Ⅱ. CONNECTION (AS INDICATED IN DIAGRAM):
Open the top cover of controller and connect the wire with terminals follow the diagram on the top cover of it.
1. Connect the “+”, “-” Poles of the battery to the corresponding ports of controller (the third and the fourth one from left).
* The subsequent operation can be processed if only if load indicator (mark: load) flickers once and starts lighting after 15 seconds. Otherwise, the subsequent operation will damage the controller.
2. Connect the “+”, “-” poles of the solar panel to the corresponding ports of controller (the first and the second one from left).
* If a connection error can damage your controller.
3. Connect the “+”, “-” poles of the load to the corresponding ports of controller (the fifth and the sixth one from left).
Ⅲ. INDICATOR LED
1. Charge LED is used to indicate the charging status of battery.
Lighting is in-charging mode, flashing is floating charge mode. LED turn off means charging stopped.
2. There is output and load can work if the Load LED is lighting. There isn’t output and the load cannot work if Load LED off.
Notice:
1. Please make sure the rated voltage of solar panels, batteries the loads are the same. All of them should be 6V, 12V or 24V.
2. The rated current of solar panels and load must be less than the rated current of controller.
Fit or replace product model: (Cross refer or compatible chart )
PWM solar panel controller
solar panel PWM charging control system
Unicell International is not affiliated in any way with any of the manufacturers listed in this catalogue and the batteries sold in this catalogue have not been sponsored or approved by any of such manufacturers. Any trademarks or model numbers listed in this catalogue are identified for compatibility or cross-reference purposes only
12V / 24V 10A PWM solar charge controller supply by UNICELL in Singapore
UNICELL a Leading IT product supplier in Singapore Malaysia Indonesia Philippines Brunei and Thailand since 1986 , we carry more the 66,000 model
Order code : SLP2010-10A
12V 24V Auto 10A Solar charge controller Solar charged protector
Product description:
12V and 24V Auto Solar charge controller, have battery capacity indicator. Also carry with overload, short circuit, lighting, under voltage, over voltage, over charged, anti-access protection.
The product is used to control Solar Panel and battery in Solar System automatically. Here is the Solar Panel Configuration list with different rated voltage (12V and 24V).
FUCTION:
1. Over-load protection
2. Short circuit protection
3. Lightning protection
4. Under-voltage protection
5. Over-charging protection
Ⅱ. CONNECTION (AS INDICATED IN DIAGRAM):
Open the top cover of controller and connect the wire with terminals follow the diagram on the top cover of it.
1. Connect the “+”, “-” Poles of the battery to the corresponding ports of controller (the third and the fourth one from left).
* The subsequent operation can be processed if only if load indicator (mark: load) flickers once and starts lighting after 15 seconds. Otherwise, the subsequent operation will damage the controller.
2. Connect the “+”, “-” poles of the solar panel to the corresponding ports of controller (the first and the second one from left).
* If a connection error can damage your controller.
3. Connect the “+”, “-” poles of the load to the corresponding ports of controller (the fifth and the sixth one from left).
Ⅲ. INDICATOR LED
1. Charge LED is used to indicate the charging status of battery.
Lighting is in-charging mode, flashing is floating charge mode. LED turn off means charging stopped.
2. There is output and load can work if the Load LED is lighting. There isn’t output and the load cannot work if Load LED off.
Notice:
1. Please make sure the rated voltage of solar panels, batteries the loads are the same. All of them should be 6V, 12V or 24V.
2. The rated current of solar panels and load must be less than the rated current of controller.
Fit or replace product model: (Cross refer or compatible chart )
PWM solar panel controller
solar panel PWM charging control system
Unicell International is not affiliated in any way with any of the manufacturers listed in this catalogue and the batteries sold in this catalogue have not been sponsored or approved by any of such manufacturers. Any trademarks or model numbers listed in this catalogue are identified for compatibility or cross-reference purposes only
